DG9233DY-T1

75ns, 50ns SPST - NO 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 8 Pins 100pA 3V 8-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9233DY-T1
Package: 8-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 145
Description: 75ns, 50ns SPST - NO 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 8 Pins 100pA 3V 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-SOIC (0.154, 3.90mm Width)
Number of Pins	8
Weight	540.001716mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	30Ohm
Terminal Finish	TIN LEAD
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	2
Supply Voltage	3V
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	30
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Power Supplies	3/5V
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Power Dissipation	400mW
Max Supply Current	1μA
Turn On Delay Time	75 ns
Number of Inputs	2
Supply Type	Single
Turn-Off Delay Time	50 ns
On-State Resistance (Max)	30Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	74 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	7pF 13pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	75ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.7V~12V
Normal Position	NO
Height	1.55mm
Length	5mm
Width	4mm
RoHS Status	Non-RoHS Compliant

DG9233DY-T1 Overview

Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 8. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used for these analog switches. This digital multiplexer has 30Ohm internal resistance. You can find the functions of the 8 pins in the datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. There should be 2.7V voltage fed to the electrical part below 2.7V. Using only a single voltage supply, this analog switch requires 2.7V~12V voltage. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. A 2 input needs to be operated.