DG9236DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Digi-Reel® |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 145Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9236 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 500nA |
| Power Dissipation | 208mW |
| Max Supply Current | 500nA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 55 ns |
| -3db Bandwidth | 800MHz |
| On-State Resistance (Max) | 145Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 55ns |
| Charge Injection | 6pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -70dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Height Seated (Max) | 0.6mm |
| Length | 1.8mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9236DN-T1-E4 Overview
Presented in 10-UFQFN, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Digi-Reel? is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 10. By its 1 channels, the electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. There are 10 pins injected into the electronic part body. A SPDT switching circuit is used for these analog switches. Look for analog switch ic variants by searching with DG9236. A 145Ohm internal resistance characterizes this multiplexer. For details about the functions of 10 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. The analog switch ic is of the Single supply type and is cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. The switch device would be able to operate with 500nA current. Using a single voltage supply, this switch device consumes 2.7V~16V volts. Put voltage above 500nA on the multiplexer to cause damage. The 2 inputs need to be operated in order to work. An output of 4 is provided by the digital multiplexer.
DG9236DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
500nA Supply Current
-3db Bandwidth: 800MHz
DG9236DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG9236DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- ATM
- Audio signal routing
- New designs requiring multiplexer functions
- Routers
- Multi-Line E1 Interface Cards
- Video signal routing
- Communications systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- MP3 players
- Video switching
