DG9253EN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Digi-Reel® |
| Published | 2016 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 182Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9253 |
| Pin Count | 16 |
| Number of Channels | 2 |
| Number of Circuits | 3 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1μA |
| Power Dissipation | 525mW |
| Turn On Delay Time | 455 ns |
| Number of Inputs | 6 |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±2.7V~5V |
| Supply Type | Dual, Single |
| Bandwidth | 480MHz |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 136 ns |
| Max Dual Supply Voltage | 5V |
| On-State Resistance (Max) | 182Ohm |
| Min Dual Supply Voltage | 2.7V |
| Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 45 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 4.6pF |
| On-state Resistance Match-Nom | 3.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 125ns |
| Charge Injection | 4.1pC |
| Channel-to-Channel Matching (ΔRon) | 3.1 Ω |
| Crosstalk | -67dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 0.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9253EN-T1-E4 Overview
Presented in 16-WFQFN, this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Digi-Reel?. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 2:1. Temperatures around -40°C~125°C TA are extended for operation. A total of 16 terminations have been recorded. A electrical component with 2 channels is capable of high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 16 series. SPDT switching circuits are used in these analog switch ics. There are 3 circuits in this multiplexer. Try searching for the analog switch ic with DG9253 if you are looking for variants. An switch multiplexer with 182Ohm internal resistance has a value of 182Ohm. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2.7V. 1μA current would be enough for this multiplexer to operate. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5V. In the case of dual power supplies, you should connect at least 2.7V. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. There are 6 inputs to be operated. This switch operates within the bandwidth of 480MHz.
DG9253EN-T1-E4 Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 480MHz
DG9253EN-T1-E4 Applications
There are a lot of Vishay Siliconix DG9253EN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Low-Voltage
- RGB switches
- Audio and video switching
- High-Voltage
- Medical
- Medical Instrumentation
- Audio signal routing
- Mechanical reed relay replacement
- Battery-powered systems
