DG9262DQ-T1-E3

75ns, 50ns SPST - NC 60Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9262 8 Pins 100pA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9262DQ-T1-E3
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 246
Description: 75ns, 50ns SPST - NC 60Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9262 8 Pins 100pA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Inquiry Now

Details

Tags

Parameters
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	75 ns
Number of Inputs	2
Supply Type	Single
Turn-Off Delay Time	50 ns
On-State Resistance (Max)	60Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	74 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	7pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	75ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.7V~12V
Drain to Source Resistance	60Ohm
Normal Position	NC
Height	850μm
Length	3mm
Width	3mm
RoHS Status	ROHS3 Compliant
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Weight	139.989945mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2012
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	60Ohm
Terminal Finish	MATTE TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG9262
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Power Supplies	3/5V

DG9262DQ-T1-E3 Overview

This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad, making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around -40°C~85°C TA are extended for operation. 8 terminations have been made so far. A high-quality output is provided by the electrical component's 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Into the electrical component body are injected 8 pins. Unlike digital switches, these are based on SPST - NC switching circuits. Use DG9262 to search for variants of the digital switches. A 60Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Single supply type digital switch with a low cost. 2.7V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 1μA current. Analogue multiplexers require a 2.7V~12V voltage to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There are SEPARATE OUTPUT outputs on this analog switch ic. There are 2 inputs to be operated. It has a Drain to Source resistance of 60Ohm ohms.