DG9262DY-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9262 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG9262DY-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 8-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 8 terminations. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching for the analog switch ic with DG9262 if you are looking for variants. An switch multiplexer with 60Ohm internal resistance has a value of 60Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. 2.7V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. A voltage of 2.7V~12V is required to drain this analog switch from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. The electrical component supports 2 inputs.
DG9262DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG9262DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG9262DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Relay replacements
- Data Acquisition Systems
- Residential Gateways, Home Gateway/Router
- Avionics
- Power routing
- Industrial control systems
- Ultrasound
- High speed data transmission line cards
- Fiber In The Loop (FITL)
