DG9263DQ-T1-E3
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9263 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG9263DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. There is an electrical component included in the 8 series. Unlike digital switches, these are based on SPST - NO switching circuits. There are 2 circuits in this switch device. Try searching for DG9263 variants of the analog switch ic. There is 60Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 8 pins functions. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Single supply type digital switch with a low cost. 2.7V is the lowest voltage that should be fed to the electronic electronic part. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~12V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA.
DG9263DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG9263DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9263DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- 65 V DACs
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Residential Gateways, Home Gateway/Router
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio and video routing
- Sample-and-hold systems
- USB 1.1 signal switching circuits
- Digital Cross-Connects
- Routers
