DG9263DY-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9263 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG9263DY-T1-E3 Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. Totally, there are 8 terminations. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. The electronic part body is injected with 8 pins. A SPST - NO switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with DG9263. It has an internal resistance of 60Ohm. For details about the functions of 8 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2.7V. For this multiplexer to operate, 1μA current would be sufficient. This analog switch requires a voltage of 2.7V~12V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It is possible to operate 2 inputs.
DG9263DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG9263DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG9263DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Low-Voltage
- Cross Connects
- Voice over IP/DSL – Integrated Access Devices, Smart
- Sample hold systems
- Access Concentrators
- MP3 players
- ATM
- HDTV
- Automotive applications
