DG9408DN-T1-E4
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 7Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 1.88W |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9408 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 1.88W |
| Max Supply Current | 1μA |
| Propagation Delay | 71 ns |
| Turn On Delay Time | 162 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 97 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 7Ohm |
| Min Dual Supply Voltage | 3V |
| High Level Output Current | 100mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 81 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 21pF 211pF |
| On-state Resistance Match-Nom | 3.6Ohm |
| Switch Time (Ton, Toff) (Max) | 70ns, 44ns |
| Charge Injection | 29pC |
| Channel-to-Channel Matching (ΔRon) | 3.6 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 94ns |
| Drain to Source Resistance | 3.9Ohm |
| Height | 950μm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9408DN-T1-E4 Overview
Due to its 16-VQFN Exposed Pad packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. Due to its 8 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. There is an electrical component included in the 16 series. The circuits in this analogue multiplexer number 1. DG9408 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 7Ohm. Datasheets for 16 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2.7V. It would be sufficient to run this analogue multiplexer with 1μA current. It may damage the digital multiplexer if the voltage is higher than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 6V. If you are using dual power supplies, you should attach at least 3V. Drain to Source resistance for this electronic component is 3.9Ohm.
DG9408DN-T1-E4 Features
8 Channels
1μA Supply Current
Drain-to-Source resistance: 3.9Ohm
DG9408DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG9408DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- PBXs
- SONET
- Precision test equipment
- Remote wireless modules
- Mechanical reed relay replacement
- Communication systems
- Communication systems
- Data Acquisition Systems
- Transmit
