Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Weight |
143.193441mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2015 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
17Ohm |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG9414 |
Pin Count |
10 |
Operating Supply Voltage |
5V |
Number of Channels |
4 |
Number of Circuits |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Propagation Delay |
128 ns |
Turn On Delay Time |
125 ns |
Logic Function |
Multiplexer |
Number of Inputs |
4 |
Supply Type |
Single |
Turn-Off Delay Time |
68 ns |
On-State Resistance (Max) |
17Ohm |
High Level Output Current |
20mA |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
58 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
10pF 24pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
55ns, 40ns |
Charge Injection |
13pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-64dB @ 1MHz |
Switch-off Time-Max |
75ns |
Voltage - Supply, Single (V+) |
2.7V~12V |
Drain to Source Resistance |
17Ohm |
Signal Current-Max |
0.02A |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG9414DQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Totally, there are 10 terminations. The electronic part delivers high-quality output through its 4 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. An injection of 10 pins is performed into the body of the electrical component. The analog switch ics are built using SP4T switching circuits. 1 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with DG9414 if you are looking for variants. Analog switches have 17Ohm internal resistance. For details about the functions of 10 pins, please refer to the datasheets. Multiplexers should not be powered above 12V in normal situations. An effective Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2.7V. This digital switch can be operated with a current of 1μA. This analogue multiplexer requires a voltage of 2.7V~12V when it drains from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. The electrical part can be operated at 5V voltage levels. A 4 input needs to be operated. There is 17Ohm resistance between Drain and Source for this electronic part.
DG9414DQ-T1-E3 Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
Drain-to-Source resistance: 17Ohm
DG9414DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9414DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Medical
- Precision data acquisition
- Industrial
- Mechanical reed relay replacement
- Power routing
- Audio/video switches
- Medical systems
- Access Concentrators
- Audio and video switching