DG9425DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 0.635mm |
| Base Part Number | DG9425 |
| Output | SEPARATE OUTPUT |
| Operating Supply Voltage | 9V |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 20nA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 56 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±3V~8V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 42 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 3Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 49pF 37pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 51ns, 35ns |
| Charge Injection | 38pC |
| Crosstalk | -77dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 1.7Ohm |
| Normal Position | NC |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9425DQ-T1-E3 Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. A SPST - NC switching circuit is used to build these analog multiplexers. Search with DG9425 if you are looking for analog multiplexer variants. An switch multiplexer with 3Ohm internal resistance has a value of 3Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. An effective Dual, Single supply digital multiplexer. There should be 2.7V voltage fed to the electrical part below 2.7V. It would be sufficient to run this analogue multiplexer with 5μA current. Put voltage above 1μA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. In the case of dual power supplies, you should connect at least 3V. This product is integrated with an analog integrated circuit (IC) of type DPDT. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages of 9V are compatible with the electrical part. It is possible to operate 4 inputs. Drain to Source resistance for this electronic component is 1.7Ohm.
DG9425DQ-T1-E3 Features
Switch Circuit: SPST - NC
5μA Supply Current
Drain-to-Source resistance: 1.7Ohm
DG9425DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9425DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Video switching
- E1 Multiplexer
- Data switching
- SDH
- Cross Connects
- Industrial and process control systems
- Communication systems
- Avionics test equipment
- Isolation
- Multiplexers
