DG9426DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Terminal Pitch | 0.635mm |
| Base Part Number | DG9426 |
| Output | SEPARATE OUTPUT |
| Qualification Status | Not Qualified |
| Power Supplies | 3/12/+-5V |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 5μA |
| Nominal Supply Current | 20nA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 57 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±3V~8V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 42 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 3Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 49pF 37pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 51ns, 35ns |
| Charge Injection | 38pC |
| Crosstalk | -77dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG9426DQ-T1-E3 Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, there are 16 terminations. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with DG9426. The internal resistance of this digital multiplexer is 3Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 12V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2.7V. This multiplexer would work with 5μA current. The analogue multiplexer may be damaged if voltage is greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 6V. With dual power supplies, you should attach at least 3V. With a DPDT analog IC integrated into the board. This analog switch ic utilizes SEPARATE OUTPUT output. There are 4 inputs to be operated.
DG9426DQ-T1-E3 Features
Switch Circuit: SPST - NO/NC
5μA Supply Current
DG9426DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG9426DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Isolation
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ATM
- E1 Multiplexer
- Private Branch Exchange (PBX)
- Data Acquisition Systems
- High-Voltage
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- PCMCIA cards
- Data switching
