DG9431DV-T1

75ns, 50ns SPDT 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 6 Pins 100pA 3V SOT-23-6 Thin, TSOT-23-6

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9431DV-T1
Package: SOT-23-6 Thin, TSOT-23-6
Datasheet: PDF
Stock: 148
Description: 75ns, 50ns SPDT 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE 6 Pins 100pA 3V SOT-23-6 Thin, TSOT-23-6(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SOT-23-6 Thin, TSOT-23-6
Number of Pins	6
Weight	19.986414mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2008
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
Resistance	30Ohm
Terminal Finish	TIN LEAD
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	1
Supply Voltage	3V
Terminal Pitch	0.95mm
Time@Peak Reflow Temperature-Max (s)	30
Pin Count	6
Number of Outputs	2
Power Supplies	3/5V
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Max Supply Current	1μA
Turn On Delay Time	75 ns
Number of Inputs	1
Supply Type	Single
Turn-Off Delay Time	50 ns
On-State Resistance (Max)	30Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	74 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	7pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	75ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.7V~5V
Drain to Source Resistance	30Ohm
Height	1mm
Length	3.05mm
Width	1.65mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant

DG9431DV-T1 Overview

Presented in SOT-23-6 Thin, TSOT-23-6, this electrical component is convenient for overseas shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 6. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. A total of 6 pins are injected into the body of the electronic part. SPDT switching circuits are used in these analog switch ics. The internal resistance of this digital multiplexer is 30Ohm. Datasheets for functions of 6 pins are available. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2.7V. An analogue multiplexer drains from a single voltage supply at 2.7V~5V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. In order to operate the 1 inputs, there are several steps to follow. There is 30Ohm resistance between Drain and Source for this electronic part. The analog switch ics has 2 outputs.