DG9431DV-T1-E3

75ns, 50ns SPDT 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9431 6 Pins 100pA 3V SOT-23-6 Thin, TSOT-23-6

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9431DV-T1-E3
Package: SOT-23-6 Thin, TSOT-23-6
Datasheet: PDF
Stock: 428
Description: 75ns, 50ns SPDT 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9431 6 Pins 100pA 3V SOT-23-6 Thin, TSOT-23-6(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SOT-23-6 Thin, TSOT-23-6
Number of Pins	6
Weight	19.986414mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
Termination	SMD/SMT
Resistance	30Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	3V
Terminal Pitch	0.95mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG9431
Pin Count	6
Number of Outputs	2
Power Supplies	3/5V
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	75 ns
Number of Inputs	1
Supply Type	Single
Turn-Off Delay Time	50 ns
On-State Resistance (Max)	30Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	74 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	7pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	75ns, 50ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	400m Ω
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2.7V~5V
Drain to Source Resistance	30Ohm
Height	1mm
Length	3.05mm
Width	1.65mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG9431DV-T1-E3 Overview

The electronic component is convenient to ship overseas because it is packed in a SOT-23-6 Thin, TSOT-23-6. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 6. A 1 channel electronic part produces high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. Into the electrical component body are injected 6 pins. These analog multiplexers are built based on SPDT switching circuits. Search with DG9431 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 30Ohm. For functions related to 6 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analog switch ics with Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 2.7V. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~5V. Putting voltage greater than 1μA on the multiplexer may cause damage. The electrical component supports 1 inputs. It has a Drain to Source resistance of 30Ohm ohms. In this digital multiplexer, there are 2 outputs.