Parameters |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
30Ohm |
Terminal Finish |
MATTE TIN |
Max Power Dissipation |
400mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG9431 |
Pin Count |
8 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Power Dissipation |
400mW |
Max Supply Current |
1μA |
Turn On Delay Time |
75 ns |
Number of Inputs |
1 |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
On-State Resistance (Max) |
30Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
74 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
7pF |
On-state Resistance Match-Nom |
0.4Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
75ns, 50ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
400m Ω |
Voltage - Supply, Single (V+) |
2.7V~5V |
Drain to Source Resistance |
30Ohm |
Height |
1.55mm |
Length |
5mm |
Width |
4mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Weight |
540.001716mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
DG9431DY-E3 Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. There is an electrical component included in the 8 series. Multiplexers built on a SPDT switching circuit are built. Try searching with DG9431 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 30Ohm. The functions of 8 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 12V. Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 2.7V. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 2.7V~5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. The electrical component supports 1 inputs. Resistivity from Drain to Source is 30Ohm for this electronic part. This digital multiplexer has 2 outputs.
DG9431DY-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 30Ohm
DG9431DY-E3 Applications
There are a lot of Vishay Siliconix DG9431DY-E3 Analog Switches & Multiplexers ICs applications.
- Power routing
- Digital access cross connects
- Fault Tolerant Systems
- Frame Relay Equipment
- RGB switches
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- USB 1.1 signal switching circuits
- T1/E1 Terminals
- Optical Applications
- E1 Network Equipment