DG9432DQ-T1-E3

35ns, 18ns SPST - NC 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9432 8 Pins 1nA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9432DQ-T1-E3
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 980
Description: 35ns, 18ns SPST - NC 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9432 8 Pins 1nA 3V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Inquiry Now

Details

Tags

Parameters
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	77 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	7.5pF 7.8pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	35ns, 18ns
Charge Injection	0.36pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-96dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	100ns
Voltage - Supply, Single (V+)	2.7V~12V
Height	850μm
Length	3mm
Width	3mm
RoHS Status	ROHS3 Compliant
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Weight	139.989945mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	60Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	320mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG9432
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Power Dissipation	320mW
Max Supply Current	-1μA
Throw Configuration	SPST
Turn On Delay Time	35 ns
Number of Inputs	2
Supply Type	Single
Turn-Off Delay Time	18 ns
On-State Resistance (Max)	30Ohm

DG9432DQ-T1-E3 Overview

Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad, this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. Electronic part bodies are injected with 8 pins. The analog switch ics are built using SPST - NC switching circuits. Try searching for DG9432 variants of the analog switch ic. Analog switches have 60Ohm internal resistance. For functions related to 8 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. Single supply type digital switch with a low cost. 2.7V is the lowest voltage the electrical component should receive. 1μA current would be enough for this multiplexer to operate. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. Put voltage above -1μA on the multiplexer to cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating the 2 inputs requires 2 inputs.