DG9432DS-T1-E3

35ns, 18ns SPST - NC 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9432 8 Pins 1nA 3V SOT-23-8

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG9432DS-T1-E3
Package: SOT-23-8
Datasheet: PDF
Stock: 395
Description: 35ns, 18ns SPST - NC 30Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG9432 8 Pins 1nA 3V SOT-23-8(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	SOT-23-8
Number of Pins	8
Weight	40.001177mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	60Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	515mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.65mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	10
Base Part Number	DG9432
Output	SEPARATE OUTPUT
Pin Count	8
Qualification Status	Not Qualified
Number of Channels	1
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Power Dissipation	515mW
Max Supply Current	-1μA
Throw Configuration	SPST
Turn On Delay Time	35 ns
Number of Inputs	2
Supply Type	Single
Turn-Off Delay Time	18 ns
On-State Resistance (Max)	30Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	77 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	7.5pF 7.8pF
On-state Resistance Match-Nom	0.4Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	35ns, 18ns
Charge Injection	0.36pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-96dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	100ns
Voltage - Supply, Single (V+)	2.7V~12V
Height	1.2mm
Length	2.9mm
Width	1.65mm
RoHS Status	ROHS3 Compliant

DG9432DS-T1-E3 Overview

Shipping overseas is convenient with the electronic component packed in SOT-23-8. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 8. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. The electrical component body receives 8 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching for the analog switch ic with DG9432 if you are looking for variants. In this multiplexer, the internal resistance is 60Ohm. To find out what the 8 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 2.7V should be applied to the electronic component. An operating current of 1μA would be sufficient for this switch device. The voltage required by this switch device is 2.7V~12V, draining from a single voltage supply. When the digital multiplexer is charged above -1μA, damage can occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. In order to operate the 2 inputs, there are several steps to follow.