DG9461DV-T1-E3
| Parameters | |
|---|---|
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~5V |
| Drain to Source Resistance | 50Ohm |
| Height | 1mm |
| Length | 3.05mm |
| Width | 1.65mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 Thin, TSOT-23-6 |
| Number of Pins | 6 |
| Weight | 19.986414mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9461 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 74 dB |
DG9461DV-T1-E3 Overview
This electronic part is conveniently packaged in SOT-23-6 Thin, TSOT-23-6, making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. Operation at a temperature around -40°C~85°C TA. There are 6 terminations totally. A electrical component with 1 channels is capable of high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 6 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for the analog switch ic with DG9461 if you are looking for variants. In this multiplexer, the internal resistance is 60Ohm. Datasheets for 6 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analogue multiplexer with a Single supply type that is cost-effective. 2.7V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1μA current. A voltage of 2.7V~5V is required for this switch device, which drains from a single voltage source. A voltage higher than 1μA may cause damage to the switch multiplexer. Among the inputs that can be operated are the 1 inputs. There is 50Ohm Drain to Source resistance on this electronic part. There are 2 outputs on the analogue multiplexer.
DG9461DV-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 50Ohm
DG9461DV-T1-E3 Applications
There are a lot of Vishay Siliconix DG9461DV-T1-E3 Analog Switches & Multiplexers ICs applications.
- Communication systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- ISDN NT1/TA
- 65 V DACs
- Industrial and process control systems
- High-Voltage
- Private Branch Exchange (PBX)
- E1 Multiplexer
- Signal routing between systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
