DG9461DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Reach Compliance Code | unknown |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~5V |
| Drain to Source Resistance | 50Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG9461DY Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 2:1. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 8. A key feature of the 8 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPDT switching circuits. It has an internal resistance of 60Ohm. Datasheets for 8 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. Analogue multiplexers require a 2.7V~5V voltage to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The 1 inputs need to be operated in order to work. A Drain to Source resistance of 50Ohm is shown for this electronic part. 2 outputs are included in the analogue multiplexer.
DG9461DY Features
Switch Circuit: SPDT
Drain-to-Source resistance: 50Ohm
DG9461DY Applications
There are a lot of Vishay Siliconix DG9461DY Analog Switches & Multiplexers ICs applications.
- Medical systems
- Intelligent PBX
- Avionics
- T1/E1 Terminals
- MP3 players
- Mechanical reed relay replacement
- PDAs
- Cross Connects
- Power routing
- Voice over IP/DSL – Integrated Access Devices, Smart
