DG9461DY-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9461 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Voltage - Supply, Single (V+) | 2.7V~5V |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | ROHS3 Compliant |
DG9461DY-E3 Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -40°C~85°C TA. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. The electronic part body is injected with 8 pins. These analog multiplexers are built based on SPDT switching circuits. DG9461 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 60Ohm. The datasheets for the 8 pins explain the functions. normally, users should not supply switches with voltages higher than 12V. Analog switch ics with Single supply type are cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. In order to operate this switch device, it would need a current of 1μA. Using only a single voltage supply, this analog switch requires 2.7V~5V voltage. When the digital multiplexer is charged above 1μA, damage can occur. A 1 input needs to be operated. Multiplexer ics with 2 outputs are available.
DG9461DY-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG9461DY-E3 Applications
There are a lot of Vishay Siliconix DG9461DY-E3 Analog Switches & Multiplexers ICs applications.
- Cell phones
- FTTH
- MP3 players
- Data Acquisition Systems
- Routers
- Intelligent PBX
- Precision data acquisition
- Frame Relay Equipment
- Cable PC
- Access Concentrators
