DG9461DY-T1-E3
| Parameters | |
|---|---|
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~5V |
| Drain to Source Resistance | 40Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9461 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 74 dB |
DG9461DY-T1-E3 Overview
The electrical component comes in 8-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Temperatures around -40°C~85°C TA are extended for operation. 8 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. A 3V voltage supply should turn on and run the electronic component. As part of its design, the 8 series is equipped with this electronic component. The analog switch ics are built using SPDT switching circuits. Try searching with DG9461 if you're looking for variants. This digital multiplexer has 60Ohm internal resistance. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. 2.7V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 1μA current. This analog switch requires a voltage of 2.7V~5V to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The 1 inputs need to be operated in order to work. A Drain to Source resistance of 40Ohm is shown for this electronic part. A analog switch ics with 2 outputs is included.
DG9461DY-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 40Ohm
DG9461DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG9461DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Precision test equipment
- Remote wireless modules
- Residential Gateways, Home Gateway/Router
- DVD-R
- High reliability control systems
- ISDN NT1/TA
- Relay Replacement
- Central office
- Audio signal routing
