DG9636EN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 200Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9636 |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 70 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 55 ns |
| -3db Bandwidth | 720MHz |
| On-State Resistance (Max) | 110Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Channel Capacitance (CS(off), CD(off)) | 2pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 55ns |
| Charge Injection | 23.5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -67dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height Seated (Max) | 0.6mm |
| Length | 1.8mm |
| RoHS Status | ROHS3 Compliant |
DG9636EN-T1-E4 Overview
Packed in 10-UFQFN, the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. Total terminations are 10. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 10 pins. These analog multiplexers are built based on SPDT switching circuits. There are 2 circuits in this multiplexer. Try searching with DG9636 if you're looking for variants. Internally, this switch multiplexer has a resistance of 200Ohm. Datasheets for 10 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users shouldn't supply more than 12V voltage to the switch device. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 2.7V should be applied to the electronic component. For this multiplexer to operate, 1nA current would be sufficient. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 500nA on the digital multiplexer, damage may occur.
DG9636EN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
-3db Bandwidth: 720MHz
DG9636EN-T1-E4 Applications
There are a lot of Vishay Siliconix DG9636EN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- High reliability control systems
- Public switching systems
- SDH
- ATM
- Medical Instrumentation
- ISDN NT1/TA
- Optical Applications
- Cross Connects
- MP3 players
