DM74ALS175M
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Supplier Device Package | 16-SOIC |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74ALS |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 50MHz |
| Base Part Number | 74ALS175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 4 |
| Clock Frequency | 50MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 3 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 14mA |
| Current - Output High, Low | 400μA 8mA |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -400μA |
| Low Level Output Current | 8mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DM74ALS175M Overview
The flip flop is packaged in 16-SOIC (0.154, 3.90mm Width). It is included in the package Tube. T flip flop uses Differentialas its output configuration. It is configured with a trigger that uses Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. It is operating at 0°C~70°C TA. Logic flip flops of this type are classified as D-Type. In this case, it is a type of FPGA belonging to the 74ALS series. Its output frequency should not exceed 50MHz Hz. The list contains 1 elements. During its operation, it consumes 14mA quiescent energy. The 74ALS175family includes it. A part of the electronic system is mounted in the way of Surface Mount. Basically, it is designed with a set of 16 pins. This device exhibits a clock edge trigger type of Positive Edge. 4bits are used in its design. The superior flexibility of this product is achieved by using 4 circuits. High efficiency requires the supply voltage to be maintained at 5V. There are no output lines on the JK flip flop. The number of input lines is 4. It is set to -400μAfor the high level output current. The low level output current is set to 8mA. It is recommended that the operating temperature be lower than 70°C. In order for the system to operate properly, the temperature should be higher than 0°C. Despite its minimal supply voltage of 4.5V, it is capable of operating. 5.5Vis the maximum supply voltage it supports. It is possible to achieve a frequency of 50MHz.
DM74ALS175M Features
Tube package
74ALS series
16 pins
4 Bits
DM74ALS175M Applications
There are a lot of ON Semiconductor DM74ALS175M Flip Flops applications.
- Divide a clock signal by 2 or 4
- CMOS Process
- Consumer
- Counters
- Storage Registers
- Power down protection
- Shift registers
- High Performance Logic for test systems
- Parallel data storage
- ATE
