DM74ALS175N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Supplier Device Package | 16-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1998 |
| Series | 74ALS |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 50MHz |
| Base Part Number | 74ALS175 |
| Function | Master Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 4 |
| Clock Frequency | 50MHz |
| Propagation Delay | 17 ns |
| Turn On Delay Time | 3 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 14mA |
| Current - Output High, Low | 400μA 8mA |
| Number of Gates | 4 |
| Number of Bits per Element | 4 |
| Max Propagation Delay @ V, Max CL | 17ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -400μA |
| Low Level Output Current | 8mA |
| Number of Input Lines | 4 |
| Number of Output Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DM74ALS175N Overview
16-DIP (0.300, 7.62mm)is the packaging method. There is an embedded version in the package Tube. It is configured with Differentialas an output. This trigger uses the value Positive Edge. In this case, the electronic component is mounted in the way of Through Hole. The supply voltage is set to 4.5V~5.5V. A temperature of 0°C~70°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. In this case, it is a type of FPGA belonging to the 74ALS series. It should not exceed 50MHzin its output frequency. In total, it contains 1 elements. During its operation, it consumes 14mA quiescent energy. You can search similar parts based on 74ALS175. It is mounted by the way of Through Hole. It is designed with 16 pins. This device has the clock edge trigger type of Positive Edge. There are 4bits in its design. Its superior flexibility is attributed to its use of 4 circuits. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. In order to operate, the chip has 4 output lines. 4input lines are available for you to choose from. High level output current is set to -400μA. A 8mAvalue is set for low-level output current. A temperature below 70°Cis recommended for operation. The operating temperature should be higher than 0°C. The system operates with a minimum supply voltage of 4.5V. 5.5Vis the maximum supply voltage supported by it. This can be achieved at a frequency of 50MHz. This building block contains 4 gates as its basic building block.
DM74ALS175N Features
Tube package
74ALS series
16 pins
4 Bits
4 gates
DM74ALS175N Applications
There are a lot of ON Semiconductor DM74ALS175N Flip Flops applications.
- Divide a clock signal by 2 or 4
- Pattern generators
- Digital electronics systems
- Load Control
- Balanced 24 mA output drivers
- Event Detectors
- High Performance Logic for test systems
- Convert a momentary switch to a toggle switch
- 2 – Bit synchronous counter
- Storage Registers
