DM74AS374N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Supplier Device Package | 20-PDIP |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Series | 74AS |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | D-Type |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Voltage - Supply | 4.5V~5.5V |
| Frequency | 125MHz |
| Base Part Number | 74AS374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Bits | 8 |
| Clock Frequency | 125MHz |
| Propagation Delay | 9 ns |
| Turn On Delay Time | 3 ns |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 120mA |
| Current - Output High, Low | 15mA 48mA |
| Number of Bits per Element | 8 |
| Max Propagation Delay @ V, Max CL | 9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| High Level Output Current | -15mA |
| Low Level Output Current | 48mA |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
DM74AS374N Overview
It is packaged in the way of 20-DIP (0.300, 7.62mm). A package named Tubeincludes it. It is configured with Tri-State, Non-Invertedas an output. This trigger uses the value Positive Edge. This electronic part is mounted in the way of Through Hole. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. It is at 0°C~70°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. The 74ASseries comprises this type of FPGA. It should not exceed 125MHzin its output frequency. There are 1 elements in it. As a result, it consumes 120mA quiescent current. The 74AS374family includes it. There is an electronic part that is mounted in the way of Through Hole. It is designed with 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. Flip flops designed with 8bits are used in this part. The superior flexibility is achieved through the use of 8 circuits. In order to achieve high efficiency, the supply voltage should be maintained at 5V. In order for the chip to function, it has 3output lines. It is reported that there are 8 input lines. A -15mAvalue is set for the high level output current. 48mA is the low level output current. Ideally, the operating temperature should be lower than 70°C. In order for the system to operate properly, the temperature should be higher than 0°C. In order for it to operate, a supply voltage of 4.5Vis required. There is a maximum voltage support of 5.5V. It is possible to achieve a frequency of 125MHz.
DM74AS374N Features
Tube package
74AS series
20 pins
8 Bits
DM74AS374N Applications
There are a lot of ON Semiconductor DM74AS374N Flip Flops applications.
- ESD performance
- Shift registers
- Single Up Count-Control Line
- Set-reset capability
- Synchronous counter
- CMOS Process
- Buffer registers
- Storage registers
- Storage Registers
- Patented noise
