DRV102FKTWTG3
| Parameters | |
|---|---|
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Surface Mount | YES |
| Number of Pins | 7 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Feature | Internal PWM, Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 24V |
| Base Part Number | DRV102 |
| Pin Count | 7 |
| Number of Outputs | 1 |
| Output Type | Bipolar |
| Operating Supply Voltage | 24V |
| Supply Voltage-Max (Vsup) | 60V |
| Interface | On/Off |
| Current - Output (Max) | 2A |
| Nominal Supply Current | 9mA |
| Output Configuration | High Side |
| Output Current | 2.7A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | Relay, Solenoid Driver |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 8V~60V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Output Peak Current Limit-Nom | 2.7A |
| Built-in Protections | OVER CURRENT; THERMAL |
| Height | 4.44mm |
| Length | 10.1mm |
| Width | 8.89mm |
DRV102FKTWTG3 Overview
It is packaged in the form of a Tape & Reel (TR).It is included with the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package as well.Surface Mount is the mounting type of the LED driver.The switch type is Relay, Solenoid Driver.Keeping the temperature at -55°C~125°C TA ensures reliable operation.The LED driver has a total of 1 outputs.The LED driving board operates at Not Required volts.A maximum output voltage of Bipolar volts has been specified.There are Internal PWM, Status Flag features available on the LED driving board.It belongs to the DRV102 family.There are 7 terminations in it.The operation is carried out using the 7 pins.There are 1 functions of the LED driver.2AV is the maximum output of the LED driver.High efficiency is possible when the supply voltage is set to 24V.It is equipped with a total of 7 pins.As a result, the output current is set to 2.7A.A self-contained LED driver with a capacity of Peripheral Drivers is contained in an econtainer.The LED driver is configured with a maximum supply voltage of 60V (Vsup).The supply voltage should be set at 24V for best efficiency.
DRV102FKTWTG3 Features
Supplied from 24V
DRV102FKTWTG3 Applications
There are a lot of Texas Instruments DRV102FKTWTG3 Power Switches ICs applications.
- Wireless Headsets
- Wireless Modem Data Cards
- USB Power Distribution
- USB Power Distribution
- Solid State Drivers
- Hard Disk Drives
- Smart Phones, Feature Phones
- PC Card Hot Swap
- Hot-Swap Systems
- Portable Music Players
