DRV8833PWP
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerTSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | DC Motors, General Purpose, Solenoids |
| Subcategory | Motion Control Electronics |
| Technology | NMOS |
| Voltage - Supply | 2.7V~10.8V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | DRV8833 |
| Pin Count | 16 |
| Number of Outputs | 2 |
| Max Output Current | 2A |
| Power Supplies | 3/10V |
| Interface | PWM |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 3mA |
| Output Configuration | Half Bridge (4) |
| Output Current | 1.5A |
| Output Current per Channel | 1.5A |
| Collector Emitter Voltage (VCEO) | 10.8V |
| Max Collector Current | 700mA |
| Voltage - Load | 2.7V~10.8V |
| RMS Current (Irms) | 1.5A |
| Fault Protection | Over Temperature, Short Circuit |
| Switching Frequency | 50kHz |
| Motor Type | Stepper |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DRV8833PWP Overview
The design includes a package of type [0].The part is packaged in a 16-PowerTSSOP (0.173, 4.40mm Width) case.Ideally, the part should be mounted by Surface Mount.The component connected in DC Motors, General Purpose, Solenoidsis compatible with it.There is a capability for the device to provide 2.7V~10.8V volts.This device operates at a temperature of -40°C~150°C TJ.This part has 16termination options.Voltage can be applied at a rate of 2.7V~10.8V volts to the load.The amplifier should be set to 5V.The device employs the BRUSH DC MOTOR CONTROLLER analog IC.This can be determined by looking at the DRV8833 part number.A device with 16pins is available.The Motion Control Electronicsseries contains it.Drivers controllers is possible to access 2outputs.Steppercan be recognized as a motor type.As it has an output current of [0], it provides maximum flexibility in design.As a result, the maximum output current reaches 2Ain order to meet the requirements of the operation.This part has a total number of pins of 16.
DRV8833PWP Features
Applications : DC Motors, General Purpose, Solenoids
Load voltage across the chip 2.7V~10.8V
base on DRV8833 number
designed with 2 outputs
Motor Type classified as Stepper
with 16 pins
DRV8833PWP Applications
There are a lot of Texas Instruments DRV8833PWP motor drivers applications.
- Lighting for health and wellbeing
- Indicator circuit
- Dome
- Dash
- Monitoring the energy that the luminaire uses
- Large outdoor LED display
- Tail lights
- Side marker lights
- Matrix LED dimmers
- Building technology
