DRV8833RTYT
| Parameters | |
|---|---|
| Interface | PWM |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 3mA |
| Output Configuration | Half Bridge (4) |
| Output Current | 1.5A |
| Output Current per Channel | 1.5A |
| Collector Emitter Voltage (VCEO) | 10.8V |
| Max Collector Current | 700mA |
| Voltage - Load | 2.7V~10.8V |
| RMS Current (Irms) | 1.5A |
| Fault Protection | Over Temperature, Short Circuit |
| Switching Frequency | 50kHz |
| Motor Type | Stepper |
| Height | 800μm |
| Length | 4mm |
| Width | 4mm |
| Thickness | 750μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | DC Motors, General Purpose, Solenoids |
| Subcategory | Motion Control Electronics |
| Technology | NMOS |
| Voltage - Supply | 2.7V~10.8V |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DRV8833 |
| Pin Count | 16 |
| Number of Outputs | 2 |
| Max Output Current | 2A |
| Power Supplies | 3/10V |
DRV8833RTYT Overview
This package was designed with Cut Tape (CT)in mind.The part is packaged in a 16-WQFN Exposed Pad case.Drivers controllers is recommended that the part be mounted by Surface Mount.Fits the component connected to DC Motors, General Purpose, Solenoids.The device is capable of supplying a voltage of 2.7V~10.8V volts.There is a temperature range of -40°C~150°C TJin which this device operates.The part supports 16terminations.You can apply voltage at 2.7V~10.8Vto the load.This amplifier should be operated at 5V.A BRUSH DC MOTOR CONTROLLERanalog integrated circuit is employed in the device.The DRV8833part number allows us to locate it.In this device, there are 16 pins.The Motion Control Electronicsseries contains it.Drivers controllers is possible to access 2outputs.Drivers controllers is possible to recognize the motor type as [0].Drivers controllers offers maximum design flexibilDrivers controllersy since Drivers controllerss output current is 1.5A.For compliance with the operation requirements, the maximum output current is [0].There are a total of 16pins on the part.
DRV8833RTYT Features
Applications : DC Motors, General Purpose, Solenoids
Load voltage across the chip 2.7V~10.8V
base on DRV8833 number
designed with 2 outputs
Motor Type classified as Stepper
with 16 pins
DRV8833RTYT Applications
There are a lot of Texas Instruments DRV8833RTYT motor drivers applications.
- AM radio
- Alternative to HID lights
- drivers for outdoor application
- Lighting for the ambience of tunability
- Commercial office
- Horticultural applications
- Indicator
- Smart lighting applications
- Handheld devices
- Camera-enabled smartphones
