DRV8838DSGT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Number of Pins | 8 |
| Weight | 10.886217mg |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Applications | DC Motors, General Purpose, Solenoids |
| Technology | NMOS |
| Voltage - Supply | 1.8V~7V |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DRV8838 |
| Max Output Current | 1.8A |
| Supply Voltage-Max (Vsup) | 7V |
| Interface | On/Off |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Operating Supply Current | 100μA |
| Output Configuration | Half Bridge (2) |
| Output Current | 1.8A |
| Voltage - Load | 0V~11V |
| Fault Protection | Over Temperature, Short Circuit |
| Number of Drivers | 1 |
| Drain to Source Resistance | 280mOhm |
| Height | 800μm |
| Length | 2mm |
| Width | 2mm |
| Thickness | 750μm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DRV8838DSGT Overview
This package was designed with Tape & Reel (TR)in mind.Drivers controllers is packaged wDrivers controllersh a 8-WFDFN Exposed Pad case.Drivers controllers is recommended to mount the part by Surface Mount.As a result, it is appropriate for the component connected to DC Motors, General Purpose, Solenoids.There is a possibility of providing 1.8V~7Vvolts through the device.This device operates at a temperature range of -40°C~150°C TJ.A total of 8terminations are available in this part.A voltage of 0V~11Vcan be applied to the load.Drivers controllers is important to note that this amplifier should be operated at the 3Vsetting.There is a recommended mounting method of Surface Mount.A BRUSH DC MOTOR CONTROLLERanalog integrated circuit is employed in this device.According to the DRV8838part number, the part is found.Drivers controllers is designed wDrivers controllersh 8 pins.With a 1.8A output current, it offers the greatest degree of design flexibility.The maximum output current reaches 1.8Ato meet the operating requirements.Controller ic uses 100μAas the supply current for Controller ics operation.Controller ic is equipped wController ich 1 drivers.
DRV8838DSGT Features
Applications : DC Motors, General Purpose, Solenoids
Load voltage across the chip 0V~11V
base on DRV8838 number
with 1 Drivers
DRV8838DSGT Applications
There are a lot of Texas Instruments DRV8838DSGT motor drivers applications.
- parking lights
- Footwell lighting
- Accurate LED current matching
- AM radio
- Alternative to HID lights
- High brightness LED lighting
- A cross between entertainment
- LED bias
- Dome
- Dash
