DS1233AZ-15+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-261-4, TO-261AA |
| Number of Pins | 4 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| Series | EconoReset |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Type | Simple Reset/Power-On Reset |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.3mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DS1233A |
| Output | Open Drain or Open Collector |
| Pin Count | 4 |
| Operating Supply Voltage | 5V |
| Power Supplies | 3.3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 50μA |
| Max Supply Current | 50μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 2.72V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 250ms Minimum |
| Min Reset Threshold Voltage | 2.64V |
| Max Reset Threshold Voltage | 2.8V |
| Threshold Voltage | +2.72V |
| Undervoltage Threshold | 2.64V |
| Overvoltage Threshold | 2.8V |
| Height | 1.8mm |
| Length | 6.7mm |
| Width | 3.7mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DS1233AZ-15+ Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 4 in total. A Tube package is used to package the power management. There are 1 functions included in this PMIC so that you can refer to them. Power management consists of 1 channels, each of which can be used independently. As a reference, this IC power includes TO-261-4, TO-261AA functions for your convenience. With power management, you get a lot of benefits that you won't find in other Simple Reset/Power-On Reset products. There is a specification for the peak reflow temperature of the package to be 260. In a 3.3V supply voltage, the power management conducts. There is a voltage supply of 1 for the PMIC chip, and the chip conducts at that voltage. Surface Mount is the one that mounts power management. The power management system can be categorized as a Power Management Circuits chip. In total, IC powers are 4 pins on the board. This power management system has 4 pins. It is recommended that the minimum supply voltage (Vsup) for this IC management should not be less than 1.2V volts. The maximum supply voltage (Vsup) in this PMIC should not exceed 5.5V volts. The recommended mounting type is Surface Mount. It is recommended that the supervisor be set to this temperature: -40°C~85°C TA. Power management has an output of Open Drain or Open Collector during operation. There is a supply current of 50μA for the power management. A similar IC managements number of the manufacturer can always be found by using DS1233A, the base power ics number. It is necessary to have 3.3V volts of power in order for this voltage supervisor to operate. At most, voltage supervisor can operate at a supply temperature of 50μA. As you can see, this IC power comes from the well-known EconoReset series of products.
DS1233AZ-15+ Features
Simple Reset/Power-On Reset type
Minimum supply voltage of 1.2V
50μA operating supply current
DS1233AZ-15+ Applications
There are a lot of Maxim Integrated DS1233AZ-15+ Voltage Supervisors applications.
- Display equipment
- Power distribution systems of infant care room
- Automotive permanent magnet synchronous motors
- Power communication system
- Medical-specific isolation transformer
- Insulation fault location system
- Digitally controlled LDO regulators circuit
- Telecommunications equipment
- DVR
- Radar
