DS1836AS-10
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | MicroManager |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Battery Backup Circuit |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Power Management Circuits |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | DS1836 |
| Output | Push-Pull, Totem Pole |
| Pin Count | 8 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.2V |
| Operating Supply Current | 55μA |
| Max Supply Current | 55μA |
| Adjustable Threshold | NO |
| Watchdog Timer | No |
| Reset | Active Low |
| Voltage - Threshold | 4.37V |
| Number of Voltages Monitored | 1 |
| Reset Timeout | 200ms Minimum |
| Min Reset Threshold Voltage | 4.25V |
| Max Reset Threshold Voltage | 4.5V |
| Threshold Voltage | +4.37V |
| Undervoltage Threshold | 4.25V |
| Overvoltage Threshold | 4.5V |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DS1836AS-10 Overview
As you can see, this power management is mounted through 8 terminals. Packaging is in the form of a Tube. Please find attached 1 functions for your reference in this IC power. Depending on the power managment ic you are looking at, you can find a total of 1 channels. Please refer to power management for 8-SOIC (0.154, 3.90mm Width) functions. This IC power shares lots of benefits with other Battery Backup Circuit products. Packages are specified to have an average peak reflow temperature of 245. IC management conducts at a voltage of 3.3V. Power ics operate at 1 supply voltages. By Surface Mount, IC management has been mounted. As a subcategory, this PMIC chip can be categorized as Power Management Circuits. Power management has a total of 8 pins. The pins of the power management system count 8. Normally, the supply voltage (Vsup) for this PMIC should not be lower than 1.2V. The maximum supply voltage (Vsup) is not to exceed 5.5V volts in this IC management. Surface Mount mounting is recommended. This range of temperature should be set for the supervisors: -40°C~85°C TA. During operation, this power management system outputs Push-Pull, Totem Pole. The supervisor's supply current is specified to 55μA. You can always use DS1836, the base supervisor number, to search for similar PMICs of the manufacturer. A power supply of 5V watts is required for the operation of this power management. Voltage supervisor can work with a supply temperature of 55μA at the most. The IC power that you are looking at comes from our well-known MicroManager series product line.
DS1836AS-10 Features
Battery Backup Circuit type
Minimum supply voltage of 1.2V
55μA operating supply current
DS1836AS-10 Applications
There are a lot of Maxim Integrated DS1836AS-10 Voltage Supervisors applications.
- Leakage current detection
- Microcontroller system
- Embedded computing
- Medical-specific insulation monitor
- DSP
- Detection of phase imbalance
- Electronics installed in the vehicle
- Multi-voltage system
- Power distribution systems of CCU
- emergency room
