DS3658N/NOPB
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.053808g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 2.075W |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 85mA |
| Base Part Number | DS3658 |
| Pin Count | 16 |
| Number of Outputs | 4 |
| Output Voltage | 70V |
| Output Type | Bipolar |
| Max Output Current | 600mA |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Nominal Supply Current | 85mA |
| Output Configuration | Low Side |
| Power Dissipation | 2.075W |
| Output Current | 600mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 85mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 500 ns |
| Switch Type | General Purpose |
| Max Input Voltage | 15V |
| Turn-Off Delay Time | 8 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.75V~5.25V |
| Interface IC Type | AND GATE BASED PERIPHERAL DRIVER |
| Driver Number of Bits | 4 |
| Turn On Time | 0.5 µs |
| Output Peak Current Limit-Nom | 0.6A |
| Built-in Protections | TRANSIENT |
| Height | 5.08mm |
| Length | 19.81mm |
| Width | 6.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DS3658N/NOPB Overview
A Tube is used to package it.This file is included in package 16-DIP (0.300, 7.62mm).In this case, the LED driving board is mounted as Through Hole.The switch type of this switch is General Purpose.To ensure reliable operation, set the temperature to 0°C~70°C TA.It is possible to use 4 outputs in the lighting driver.It uses a supply voltage of Not Required to operate.A maximum output voltage of Bipolar volts can be obtained with this LED driver.I believe it belongs to the DS3658 family.It consists of 16 terminations in total.The operation is performed through the 16 pins.It has 1 functions.As a result, the maximum output current is reduced to 600mA in order to meet the operation requirements.It is possible to achieve a high level of efficiency with a supply voltage of 5V.It is mounted in the way of Through Hole.As a result, it has a total of 16 pins.This case has the output current set to 600mA.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.A maximum supply voltage of 5.25V is set in Vsup.This part has a power supply of 5V volts.Its maximum input voltage is 15V volts.For its operation, a maximum current requirement of 85mA is required.There is a type AND GATE BASED PERIPHERAL DRIVER interface to the LED driving board.
DS3658N/NOPB Features
Supplied from 5V
DS3658N/NOPB Applications
There are a lot of Texas Instruments DS3658N/NOPB Power Switches ICs applications.
- Portable GPS
- Various applications equipped with buttons
- HDD, SSD
- Portable Music Players
- Hot-Swap Systems
- Notebook and Tablet Computers
- Wireless/Networking Cards
- Hard Disk Drives
- Telecom and Network Systems
- Storage (HDDs, SSDs)
