banner_page

E-L9826

N-Channel 1.27mm PMIC L9826 20 Pin 3MHz 5V 20-SOIC (0.295, 7.50mm Width)


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-E-L9826
  • Package: 20-SOIC (0.295, 7.50mm Width)
  • Datasheet: PDF
  • Stock: 383
  • Description: N-Channel 1.27mm PMIC L9826 20 Pin 3MHz 5V 20-SOIC (0.295, 7.50mm Width) (Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 6 months ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 20-SOIC (0.295, 7.50mm Width)
Number of Pins 20
Operating Temperature -40°C~150°C TJ
Packaging Tube
Part Status Active
Moisture Sensitivity Level (MSL) 3 (168 Hours)
Number of Terminations 20
ECCN Code EAR99
Resistance 1.5Ohm
Terminal Position DUAL
Terminal Form GULL WING
Number of Functions 1
Supply Voltage 5V
Terminal Pitch 1.27mm
Frequency 3MHz
Base Part Number L9826
Pin Count 20
Number of Outputs 8
Output Type N-Channel
Max Output Current 1A
Supply Voltage-Max (Vsup) 5.5V
Supply Voltage-Min (Vsup) 4.5V
Interface SPI
Nominal Supply Current 5mA
Output Configuration Low Side
Voltage - Supply (Vcc/Vdd) 4.5V~5.5V
Max Supply Current 5mA
Propagation Delay 100 ns
Turn On Delay Time 10 μs
Switch Type Latched Driver
Output Current per Channel 450mA
Turn-Off Delay Time 10 μs
Ratio - Input:Output 1:8
Voltage - Load 45V Max
Fault Protection Current Limiting (Fixed), Over Temperature
Output Peak Current Limit-Nom 1A
Rds On (Typ) 1.5 Ω
Built-in Protections TRANSIENT; OVER CURRENT; THERMAL
Output Current Flow Direction SINK
Height Seated (Max) 2.65mm
Width 7.5mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

E-L9826 Overview


The LED driver's packaged as a Tube.It's included in the 20-SOIC (0.295, 7.50mm Width) package.Surface Mount is the mounting type of the LED driver.Latched Driver is the type of switch owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.The LED driver has 8 outputs.A voltage of 4.5V~5.5V is used to power it.There is a maximum output voltage of N-Channel volts.It belongs to the family L9826.It contains 20 terminations.The 20 pins are used for the operation of the system.It consists of 1 functions.The maximum output current is reduced to 1A to meet the operation criteria.It is possible to achieve a high level of efficiency with a supply voltage of 5V.The LED driving board is mounted in the way of Surface Mount.20 pins are connected to it in total.In this case, there is 1.5Ohm resistance in the LED driving board.The maximum supply voltage for this LED driver is 5.5V (Vsup).In order to operate normally, the supply voltage (Vsup) must be maintained above 4.5V.There is a maximum current requirement of 5mA for its operation.

E-L9826 Features


Supplied from 5V
Resistance of 1.5Ohm

E-L9826 Applications


There are a lot of STMicroelectronics E-L9826 Power Switches ICs applications.

  • Hot Swap
  • Wireless Headsets
  • Hard Disk Drives
  • Wireless Modem Data Cards
  • Solid State Drivers
  • Mobile Communication Devices
  • PDAs
  • Wireless/Networking Cards
  • Smartphone and PDA
  • Notebook PC

Write a review

Note: HTML is not translated!
    Bad           Good