EL5104IWZ-T7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOT-23-6 |
| Packaging | Cut Tape |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 6 |
| JESD-30 Code | R-PDSO-G6 |
| Operating Supply Voltage | 12V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 9.5mA |
| Nominal Supply Current | 11mA |
| Slew Rate | 3000 V/μs |
| Common Mode Rejection Ratio | 62 dB |
| Current - Input Bias | 8μA |
| Output Current per Channel | 160mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 700000 kHz |
| Voltage Gain | 65dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Max Dual Supply Voltage | 6.6V |
| -3db Bandwidth | 700MHz |
| Min Dual Supply Voltage | 2V |
| Consumer IC Type | VIDEO AMPLIFIER |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EL5104IWZ-T7 Overview
Packaging for the buffer amplifier is in the form of a SOT-23-6 case. Instrumentation amplifier is delivered in a Cut Tape case. There have been a total of 6 terminations over the past year. There are a total of 6 pins on this op amp. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. As long as the supply current of the chip does not exceed 9.5mA, this op amp ic can operate. Op amp is a member of the 65dB's 65dB family. On the buffer amps, there are 1 channels that can be used. This op amp needs to be operated at a temperature of not less than -40°C degrees Celsius in order to function properly. In order to avoid damage to the product, operational amplifiers should only be used at temperatures below 85°C. The operating supply voltage of instrumentation amplifier is rated 12V voltage. It is important to keep in mind that the power supply voltage of this electric component is below 10V, which is suitable. In order to ensure that the instrumentation amplifier's supply voltage remains above 4V, it is recommended to keep it higher. This electrical part should be conducted under the dual supply voltage of 6.6V volts when you conduct this part. In order to sort customer IC types, use VIDEO AMPLIFIER.
EL5104IWZ-T7 Features
6 Pins
65dB voltage gain
EL5104IWZ-T7 Applications
There are a lot of Intersil (Renesas Electronics America) EL5104IWZ-T7 Instrumentational OP Amps applications.
- Portable docking station
- High input resistance broadband
- Subtraction operation circuits
- Television
- Computer workstations
- Television broadcasting equipment
- Micro signal measurement
- Semiconductor detectors
- Industrial control system
- Portable media players
