EL5170ISZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 8 |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 4.75V |
| Operating Supply Current | 7.4mA |
| Nominal Supply Current | 8.4mA |
| Max Supply Current | 8.4mA |
| Current - Output | 60A |
| Slew Rate | 1100 V/μs |
| Common Mode Rejection Ratio | 84 dB |
| Current - Input Bias | 6μA |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 25mV |
| Bandwidth | 100MHz |
| Gain Bandwidth Product | 100MHz |
| Differential Output | YES |
| Power Supply Rejection Ratio (PSRR) | 83dB |
| Gain | 2 dB |
| Input Characteristics | DIFFERENTIAL |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 100MHz |
| Interface IC Type | LINE DRIVER |
| Min Dual Supply Voltage | 2.25V |
| Dual Supply Voltage | 5V |
| Interface Standard | GENERAL PURPOSE |
| Number of Drivers | 1 |
| Negative Supply Voltage-Nom | -5V |
| Out Swing-Min | 6.3 V |
| Height | 1.45mm |
| Length | 4.9mm |
| Width | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EL5170ISZ Overview
In order to protect the op amps, a SOIC case is used. It is estimated that there will be 8 terminations in the next few months. Please take in mind that this instrumentation amplifier should be run at 5V. Instrumentation amplifier is a part of Line Driver or Receivers. In total, the buffer amplifier consists of 8 pins. Op amp rates 25mV as input offset voltage. A supply current of 7.4mA can be used to operate this linear amplifier. The temperature should not be lower than -40°C for operational amplifier ics to operate. A temperature greater than 85°C should not be used for the operation of this instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 5V voltage. With regard to the supply voltage, this electrical component is capable of working from under 10V. To keep the buffer amps' supply voltage higher than 4.75V. There should be a dual supply voltage of 6V for you to conduct this electrical part. The interface IC of the electronic part is classified as LINE DRIVER.
EL5170ISZ Features
supply voltage of 5V
EL5170ISZ Applications
There are a lot of Intersil (Renesas Electronics America) EL5170ISZ Instrumentational OP Amps applications.
- Mobile phone
- Signal filtering
- Signal amplification
- Video data acquisition
- Integrator circuits
- Portable media players
- PDA
- Exponential operation circuits
- Video conversion and routing
- Inverse/same-phase proportional circuit
