EPCS1SI8N
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2010 |
| Series | EPCS |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | 3A991.B.1.B.1 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| HTS Code | 8542.32.00.51 |
| Subcategory | Flash Memories |
| Technology | CMOS |
| Voltage - Supply | 2.7V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | EPCS1 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 3.6V |
| Power Supplies | 3.3V |
| Supply Voltage-Min (Vsup) | 3V |
| Programmable Type | In System Programmable |
| Memory Size | 1Mb |
| Operating Mode | SYNCHRONOUS |
| Clock Frequency | 20MHz |
| Supply Current-Max | 0.015mA |
| Organization | 1MX1 |
| Memory Width | 1 |
| Standby Current-Max | 0.00005A |
| Memory Density | 1048576 bit |
| Parallel/Serial | SERIAL |
| Memory IC Type | CONFIGURATION MEMORY |
| Endurance | 100000 Write/Erase Cycles |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
EPCS1SI8N Overview
FPGA uses a nice 8-SOIC (0.154, 3.90mm Width) package that makes FPGA easy to use.Packaging for the external use of Tube.Licensed to operate in -40°C~85°C.FPGA is programmable through In System Programmable.FPGA is powered by a voltage which is 2.7V~3.6V volts, and this voltage is the voltage from which the generator is powered.There is a memory device mounted in Surface Mount position for this device.A maximum of 1Mb bytes of data can be stored.In addition to this part, you can search "EPCS1" for other similar parts.The supply voltage is 3.3V.There are different functions that can be applied on the 8 axis when it comes to terminating.This memory device can be used with a maximum voltage of 3.6V.3V is the minimum voltage required to supply the device.FPGA is a CONFIGURATION MEMORY memory chip that we are talking about here.If you're reflow soldering, you shouldn't go above 260.In this memory, data is transmitted using the SERIAL process.The memory chip is allowed to operate at a voltage that is no greater than 0.015mA.I think it's important to point out that this is a memory IC that has a 20MHz frequency that can be operated at.The use of 3.3V power supplies is recommended.Among the EPCS series of devices, it is one of the most popular ones.I think of it as a sort of Flash Memories.
EPCS1SI8N Features
Operating temperature: -40°C~85°C.
In System Programmable program capability.
CONFIGURATION MEMORY memory IC.
SERIAL processing.
EPCS1SI8N Applications
There are a lot of Intel EPCS1SI8N applications of configuration proms for FPGAs.
- graphics card
- mainframes
- workstations,
- personal computers
- multimedia computers
- eSRAM
- hard disk drive (HDD)
- nonvolatile BIOS memory
- cell phones
- servers
