EPM240T100C5
| Parameters | |
|---|---|
| Package / Case | TQFP |
| Number of Pins | 100 |
| Packaging | Bulk |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | 0°C |
| Additional Feature | IT CAN ALSO OPERATE AT 3.3V |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 2.5V |
| Frequency | 1.8797GHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | COMMERCIAL EXTENDED |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.375V |
| Memory Size | 1kB |
| Operating Supply Current | 55mA |
| Number of I/O | 80 |
| Nominal Supply Current | 55mA |
| Memory Type | FLASH |
| Propagation Delay | 7.5 ns |
| Turn On Delay Time | 7.5 ns |
| Frequency (Max) | 304MHz |
| Number of Logic Elements/Cells | 240 |
| Number of Programmable I/O | 80 |
| Number of Logic Blocks (LABs) | 24 |
| Speed Grade | 5 |
| Output Function | MACROCELL |
| Number of Macro Cells | 192 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 1.2mm |
| Length | 14mm |
| Width | 14mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
EPM240T100C5 Overview
The mobile phone network has 192 macro cells, which are cells that provide radio coverage from high-power cell sites (towers, antennas, or masts).You can find it in package [0].As you can see, this device has 80 I/O ports programmed into it.There is a 100terminations set on devices.This electrical part is wired with a terminal position of QUAD.A voltage of 2.5V is used as the power supply for this device.It is a part of the family [0].It is recommended that the chip be packaged by Bulk.There are 100pins on the chip.It is also possible to find IT CAN ALSO OPERATE AT 3.3Vwhen using this device.In order to achieve high efficiency, the supply voltage should be maintained at [0].For data storage, FLASHis adopted.In this case, Surface Mountis used to mount the electronic component.The device is designed with pins [0].In this case, the maximum supply voltage is 3.6V.The minimal supply voltage is 2.375V.A total of 80programmable I/Os are available.This frequency can be achieved at 1.8797GHz.In order to operate, the temperature should be higher than 0°C.A temperature lower than 85°Cis recommended for operation.Its basic building block is composed of 24 logic blocks (LABs).In order to form a fundamental building block, there are 240logic elements/cells.It is recommended that the maximum frequency is less than 0.In the devices, there is a memory of 1kBthat can be used to store programs and data.
EPM240T100C5 Features
TQFP package
80 I/Os
100 pin count
100 pins
24 logic blocks (LABs)
EPM240T100C5 Applications
There are a lot of Altera EPM240T100C5 CPLDs applications.
- Power Meter SMPS
- USB Bus
- Dedicated input registers
- Software Configuration of Add-In Boards
- STANDARD SERIAL INTERFACE UART
- ROM patching
- DMA control
- Random logic replacement
- ON-CHIP OSCILLATOR CIRCUIT
- Synchronous or asynchronous mode
