EPM570GT100C3N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Packaging | Bulk |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | 0°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Frequency | 304MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 100 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 1.8V |
| Temperature Grade | OTHER |
| Max Supply Voltage | 1.89V |
| Min Supply Voltage | 1.71V |
| Memory Size | 1kB |
| Operating Supply Current | 40mA |
| Number of I/O | 76 |
| Nominal Supply Current | 40mA |
| Memory Type | FLASH |
| Propagation Delay | 5.4 ns |
| Turn On Delay Time | 5.4 ns |
| Frequency (Max) | 304MHz |
| Number of Logic Elements/Cells | 570 |
| Number of Programmable I/O | 76 |
| Number of Logic Blocks (LABs) | 57 |
| Speed Grade | 3 |
| Output Function | MACROCELL |
| Number of Macro Cells | 440 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 1.2mm |
| Length | 14mm |
| Width | 14mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EPM570GT100C3N Overview
There are 440 macro cells. A macro cell is a cell in a mobile phone network that provides radio coverage through the use of a high-power cell site (tower, antenna or mast).TQFPis the package in which it resides.As a result, it has 76 I/O ports programmed.It is programmed to terminate devices at [0].This electrical component has a terminal position of 0.An electrical supply voltage of 1.8V is used to power it.The part belongs to Programmable Logic Devices family.Bulkshould be used to package the chip.In this chip, the 100pins are programmed.A high level of efficiency can be achieved by maintaining the supply voltage at [0].In general, it is recommended to store data in [0].The electronic component is mounted by Surface Mount.The 100pins are designed into the board.It operates at a maximum supply voltage of 1.89V volts.Initially, it requires a voltage of 1.71Vas the minimum supply voltage.There are 76 programmable I/Os in this system.A frequency of 304MHzcan be achieved.There should be a temperature above 0°Cat the time of operation.The operating temperature should be lower than 85°C.Its basic building block is composed of 57 logic blocks (LABs).A fundamental building block consists of 570logic elements/cells.It is recommended that the maximum frequency is less than 0.Devices are equipped with a memory capacity of 1kBfor storing programs and data.
EPM570GT100C3N Features
TQFP package
76 I/Os
100 pin count
100 pins
57 logic blocks (LABs)
EPM570GT100C3N Applications
There are a lot of Altera EPM570GT100C3N CPLDs applications.
- Battery operated portable devices
- Interface bridging
- Software Configuration of Add-In Boards
- Synchronous or asynchronous mode
- Wireless Infrastructure Base Band Unit and Remote Radio Unit
- PULSE WIDTH MODULATION (PWM)
- Software-Driven Hardware Configuration
- Page register
- USB Bus
- D/T registers and latches
