EPM570T100C3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Packaging | Bulk |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | 0°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 3.01205GHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | COMMERCIAL EXTENDED |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 2.375V |
| Memory Size | 1kB |
| Operating Supply Current | 55mA |
| Number of I/O | 76 |
| Nominal Supply Current | 55mA |
| Memory Type | FLASH |
| Propagation Delay | 5.4 ns |
| Turn On Delay Time | 5.4 ns |
| Frequency (Max) | 304MHz |
| Number of Logic Elements/Cells | 570 |
| Number of Programmable I/O | 76 |
| Number of Logic Blocks (LABs) | 57 |
| Speed Grade | 3 |
| Output Function | MACROCELL |
| Number of Macro Cells | 440 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 1.2mm |
| Length | 14mm |
| Width | 14mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
EPM570T100C3 Overview
Currently, there are 440 macro cells, which are low-power cell sites (towers, antennas, masts) that serve as radio coverage.It is contained in package [0].As you can see, this device has 76 I/O ports programmed into it.Devices are programmed with terminations of [0].Its terminal position is QUAD.The device is powered by a voltage of 2.5V volts.There is a part included in Programmable Logic Devices.It is recommended that the chip be packaged by Bulk.It has 100pins programmed.High efficiency requires a voltage supply of [0].In order to store data, FLASHis used.This electronic part is mounted in the way of Surface Mount.There are 100 pins embedded in the device.There is a maximum supply voltage of 3.6Vwhen the device is operating.Initially, it requires a voltage of 2.375Vas the minimum supply voltage.There are 76 programmable I/Os in this system.There is a maximum frequency of 3.01205GHz.Ideally, the operating temperature should be greater than 0°C.It is recommended that the operating temperature be lower than 85°C.There are 57logic blocks (LABs) that make up its basic building block.In order to form a fundamental building block, there are 570 logic elements or cells.If the maximal frequency is less than [0], it should be lower than that.The devices embed a memory of 1kB available for storing programs and datas.
EPM570T100C3 Features
TQFP package
76 I/Os
100 pin count
100 pins
57 logic blocks (LABs)
EPM570T100C3 Applications
There are a lot of Altera EPM570T100C3 CPLDs applications.
- Custom state machines
- Parity generators
- Cross-Matrix Switch
- High speed graphics processing
- Boolean function generators
- Software Configuration of Add-In Boards
- Pattern recognition
- Synchronous or asynchronous mode
- USB Bus
- Voltage level translation
