EPM7064AETI100-7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 166.67MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
| Number of Outputs | 68 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 68 |
| Memory Type | EEPROM |
| Propagation Delay | 7.5 ns |
| Turn On Delay Time | 7.5 ns |
| Frequency (Max) | 222.2MHz |
| Architecture | PLA-TYPE |
| Programmable Logic Type | EE PLD |
| Number of Gates | 1250 |
| Number of Programmable I/O | 68 |
| Number of Logic Blocks (LABs) | 4 |
| Speed Grade | 7 |
| Output Function | MACROCELL |
| Number of Macro Cells | 64 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height | 1mm |
| Length | 14mm |
| Width | 14mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
EPM7064AETI100-7 Overview
The mobile phone network has 64 macro cells, which are cells that provide radio coverage from high-power cell sites (towers, antennas, or masts).A TQFP package contains the item.The device is programmed with 68 I/O ports.The termination of a device is set to [0].This electrical part has a terminal position of QUADand is connected to the ground.A voltage of 3.3V is used as the power supply for this device.It is a part of family [0].There are 100 pins on the chip.In digital circuits, there are 1250gates, which act as a basic building block.A high level of efficiency can be achieved by maintaining the supply voltage at [0].It is recommended to store data in [0].Surface Mountis used to mount this electronic component.A total of 100pins are provided on this board.A maximum voltage of 3.6Vis required for operation.Initially, it requires a voltage of 3Vas the minimum supply voltage.A programmable I/O count of 68 has been recorded.The frequency that can be achieved is 166.67MHz.It is recommended that the operating temperature exceeds -40°C.It is recommended that the operating temperature be lower than 85°C.There are 4 logic blocks (LABs) in its basic building block.A maximum frequency of less than 222.2MHzis recommended.Programmable logic types can be divided into EE PLD.This device has 68outputs configured.
EPM7064AETI100-7 Features
TQFP package
68 I/Os
100 pin count
100 pins
4 logic blocks (LABs)
68 outputs
EPM7064AETI100-7 Applications
There are a lot of Altera EPM7064AETI100-7 CPLDs applications.
- Digital multiplexers
- D/T registers and latches
- PULSE WIDTH MODULATION (PWM)
- Page register
- Custom state machines
- Boolean function generators
- Dedicated input registers
- Network Interface Card (NIC) and Host Bus Adapter (HBA)
- White goods (Washing, Cold, Aircon ,...)
- Power up sequencing
