EPM7064AETI44-7N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 44 |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 44 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.8mm |
| Frequency | 135.1MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 44 |
| Number of Outputs | 36 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 36 |
| Memory Type | EEPROM |
| Propagation Delay | 7.5 ns |
| Turn On Delay Time | 7.5 ns |
| Frequency (Max) | 222.2MHz |
| Architecture | PLA-TYPE |
| Programmable Logic Type | EE PLD |
| Number of Gates | 1250 |
| Number of Logic Blocks (LABs) | 4 |
| Speed Grade | 7 |
| Output Function | MACROCELL |
| Number of Macro Cells | 64 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height | 950μm |
| Length | 10mm |
| Width | 10mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EPM7064AETI44-7N Overview
There are 64 macro cells, which are cells in a mobile phone network that provides radio coverage served by a high-power cell site (tower, antenna or mast).In the TQFPpackage, you will find it.The device is programmed with 36 I/Os.The termination of a device is set to [0].Its terminal position is QUAD.It is powered from a supply voltage of 3.3V.This part is included in Programmable Logic Devices.With 44pins programmed, the chip is ready to use.A digital circuit can be constructed using 1250gates.For high efficiency, the supply voltage should be maintained at [0].In general, it is recommended to store data in [0].Surface Mountis used to mount this electronic component.44pins are included in its design.This device operates at a voltage of 3.6Vas its maximum supply voltage.The device is designed to operate with a minimal supply voltage of 3VV.There can be 135.1MHz frequency achieved.It is recommended that the operating temperature exceeds -40°C.The operating temperature should be lower than 85°C.The logic block consists of 4 l logic blocks (LABs).Maximum frequency should be less than 222.2MHz.There is a type of programmable logic called EE PLD.There is an output of 36configured on the device.
EPM7064AETI44-7N Features
TQFP package
36 I/Os
44 pin count
44 pins
4 logic blocks (LABs)
36 outputs
EPM7064AETI44-7N Applications
There are a lot of Altera EPM7064AETI44-7N CPLDs applications.
- SUPERVISORY FUNCTION (LVD AND WATCHDOG)
- Multiple DIP Switch Replacement
- ToR/Aggregation/Core Switch and Router
- Reset swapping
- Digital systems
- Power up sequencing
- Custom state machines
- State machine design
- Synchronous or asynchronous mode
- I2C BUS INTERFACE
