EPM7064LC44-15
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | PLCC |
| Number of Pins | 44 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 44 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 220 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Frequency | 151.5MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 44 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of I/O | 36 |
| Memory Type | EEPROM |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 15 ns |
| Frequency (Max) | 151.5MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 1250 |
| Number of Programmable I/O | 36 |
| Number of Logic Blocks (LABs) | 4 |
| Speed Grade | 15 |
| Output Function | MACROCELL |
| Number of Macro Cells | 64 |
| JTAG BST | NO |
| In-System Programmable | NO |
| Height | 3.81mm |
| Length | 16.59mm |
| Width | 16.59mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
EPM7064LC44-15 Overview
There are 64 macro cells, which are cells in a mobile phone network that provides radio coverage served by a high-power cell site (tower, antenna or mast).You can find it in package [0].There are 36 I/Os on the board.It is programmed to terminate devices at [0].This electrical part is wired with a terminal position of QUAD.A voltage of 5V is used as the power supply for this device.It is a part of family [0].There are 44pins on the chip.A digital circuit can be constructed using 1250gates.If high efficiency is desired, the supply voltage should be kept at [0].EEPROM is adopted for storing data.The electronic part is mounted by Surface Mount.The device is designed with pins [0].There is a maximum supply voltage of 5.25Vwhen the device is operating.A minimum supply voltage of 4.75V is required for it to operate.There is 5V power supply available for it.A total of 36Programmable I/Os are present.It is possible to achieve a frequency of 151.5MHz.It is recommended that the operating temperature be higher than 0°C.Ideally, the operating temperature should be below 70°C.There are 4 logic blocks (LABs) in its basic building block.The maximum frequency should not exceed 151.5MHz.There is a type of programmable logic called EE PLD.
EPM7064LC44-15 Features
PLCC package
36 I/Os
44 pin count
44 pins
5V power supplies
4 logic blocks (LABs)
EPM7064LC44-15 Applications
There are a lot of Altera EPM7064LC44-15 CPLDs applications.
- Portable digital devices
- STANDARD SERIAL INTERFACE UART
- Boolean function generators
- PULSE WIDTH MODULATION (PWM)
- Wide Vin Industrial low power SMPS
- D/T registers and latches
- Programmable power management
- Page register
- Digital systems
- Power automation
