EPM7128AETI100-7N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | 3A991 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 166.67MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
| Number of Outputs | 84 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 84 |
| Memory Type | EEPROM |
| Propagation Delay | 7.5 ns |
| Turn On Delay Time | 7.5 ns |
| Frequency (Max) | 192.3MHz |
| Architecture | PLA-TYPE |
| Programmable Logic Type | EE PLD |
| Number of Gates | 2500 |
| Number of Programmable I/O | 84 |
| Number of Logic Blocks (LABs) | 8 |
| Speed Grade | 7 |
| Output Function | MACROCELL |
| Number of Macro Cells | 128 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height | 1mm |
| Length | 14mm |
| Width | 14mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EPM7128AETI100-7N Overview
Currently, there are 128 macro cells, which are low-power cell sites (towers, antennas, masts) that serve as radio coverage.There is a TQFP package containing it.The device is programmed with 84 I/O ports.The device is programmed with 100 terminations.QUADis the terminal position of this electrical part.The power supply voltage is 3.3V.This part is included in Programmable Logic Devices.There are 100 pins on the chip.A digital circuit is built using 2500gates.The supply voltage should be maintained at 3.3V for high efficiency.In general, it is recommended to store data in [0].The electronic component is mounted by Surface Mount.A total of 100pins are provided on this board.A maximum supply voltage of 3.6Vis used in its operation.A minimum supply voltage of 3V is required for it to operate.A total of 84programmable I/Os are available.This can be achieved at a frequency of 166.67MHz.Ideally, the operating temperature should be greater than -40°C.It is recommended that the operating temperature be below 85°C.In its simplest form, it consists of 8 logic blocks (LABs).The maximum frequency should not exceed 192.3MHz.A programmable logic type is classified as EE PLD.It is configured with an output of 84.
EPM7128AETI100-7N Features
TQFP package
84 I/Os
100 pin count
100 pins
8 logic blocks (LABs)
84 outputs
EPM7128AETI100-7N Applications
There are a lot of Altera EPM7128AETI100-7N CPLDs applications.
- DMA control
- Timing control
- Power automation
- Boolean function generators
- LED Lighting systems
- State machine control
- Preset swapping
- Wide Vin Industrial low power SMPS
- Code converters
- ToR/Aggregation/Core Switch and Router
