EPM7256AETI100-7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | 3A991 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | YES |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 166.67MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 84 |
| Memory Type | EEPROM |
| Propagation Delay | 7.5 ns |
| Turn On Delay Time | 7.5 ns |
| Frequency (Max) | 172.4MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 5000 |
| Number of Programmable I/O | 84 |
| Number of Logic Blocks (LABs) | 16 |
| Speed Grade | 7 |
| Output Function | MACROCELL |
| Number of Macro Cells | 256 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Length | 14mm |
| Width | 14mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
EPM7256AETI100-7 Overview
There are 256 macro cells, which provide radio coverage via high-power cell towers, antennas or masts in a mobile phone network.In the TQFPpackage, you will find it.There are 84 I/Os on the board.There are 100 terminations programmed into the device.Its terminal position is QUAD.An electrical supply voltage of 3.3V is used to power it.This part is included in Programmable Logic Devices.100pins are programmed on the chip.When using this device, YEScan also be found.There are 5000 gates, which are devices that acts as a building block for digital circuits. For high efficiency, the supply voltage should be maintained at [0].Data is stored using [0].The electronic component is mounted by Surface Mount.This board has 100 pins.It operates at a maximum supply voltage of 3.6V volts.With a minimal supply voltage of [0], it operates.A total of 84Programmable I/Os are present.This frequency is 166.67MHz.In order to operate properly, the operating temperature should be higher than -40°C.A temperature less than 85°Cshould be used for operation.The logic block consists of 16 l logic blocks (LABs).Maximum frequency should be less than 172.4MHz.A programmable logic type is classified as EE PLD.
EPM7256AETI100-7 Features
TQFP package
84 I/Os
100 pin count
100 pins
16 logic blocks (LABs)
EPM7256AETI100-7 Applications
There are a lot of Altera EPM7256AETI100-7 CPLDs applications.
- Battery operated portable devices
- Programmable power management
- Power up sequencing
- INTERRUPT SYSTEM
- Address decoders
- Synchronous or asynchronous mode
- Power automation
- Complex programmable logic devices
- TIMERS/COUNTERS
- Custom state machines
