EPM7256BTC100-10N
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Power Supplies | 1.8/3.32.5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 84 |
| Memory Type | EEPROM |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 10 ns |
| Frequency (Max) | 188.7MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 5000 |
| Number of Programmable I/O | 84 |
| Number of Logic Blocks (LABs) | 16 |
| Speed Grade | 10 |
| Output Function | MACROCELL |
| Number of Macro Cells | 256 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 1.27mm |
| Length | 14mm |
| Width | 14mm |
| RoHS Status | RoHS Compliant |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | 3A991 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | YES |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 125MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 100 |
EPM7256BTC100-10N Overview
256macrocells exist, which are cells in a mobile phone network that are primarily composed of high-power towers, antennas, or masts.It is embedded in the TQFP package.There are 84 I/Os programmed in it.There are 100 terminations programmed into the device.This electrical component has a terminal position of 0.The device is powered by a voltage of 2.5V volts.This part is part of the family [0].With 100pins programmed, the chip is ready to use.If this device is used, you will also be able to find [0].For digital circuits, there are 5000gates. These devices serve as building blocks.It is recommended that data be stored in [0].A Surface Mountis mounted on this electronic component.There are 100pins on it.A maximum voltage of 3.6Vis required for operation.The minimal supply voltage is 3V.A power supply of 1.8/3.32.5Vis required to operate it.A total of 84 Programmable I/Os are available.You can achieve 125MHzfrequencies.It is recommended that the operating temperature exceeds 0°C.It is recommended that the operating temperature be below 70°C.The logic block consists of 16 l logic blocks (LABs).It is recommended that the maximum frequency is less than 0.There is a type of programmable logic called EE PLD.
EPM7256BTC100-10N Features
TQFP package
84 I/Os
100 pin count
100 pins
1.8/3.32.5V power supplies
16 logic blocks (LABs)
EPM7256BTC100-10N Applications
There are a lot of Altera EPM7256BTC100-10N CPLDs applications.
- Handheld digital devices
- Cross-Matrix Switch
- Power automation
- State machine design
- Complex programmable logic devices
- Preset swapping
- I/O PORTS (MCU MODULE)
- Reset swapping
- USB Bus
- TIMERS/COUNTERS
