EPM7256BTI100-7N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | TQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | 3A991 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | YES |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Frequency | 166.67MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 100 |
| Qualification Status | Not Qualified |
| Power Supplies | 1.8/3.32.5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 84 |
| Memory Type | EEPROM |
| Propagation Delay | 7.5 ns |
| Frequency (Max) | 188.7MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 5000 |
| Number of Programmable I/O | 84 |
| Number of Logic Blocks (LABs) | 16 |
| Output Function | MACROCELL |
| Number of Macro Cells | 256 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 1.27mm |
| Length | 14mm |
| Width | 14mm |
| RoHS Status | RoHS Compliant |
EPM7256BTI100-7N Overview
256macrocells exist, which are cells in a mobile phone network that are primarily composed of high-power towers, antennas, or masts.You can find it in package [0].As a result, it has 84 I/O ports programmed.Terminations of devices are set to [0].As the terminal position of this electrical part is [0], it serves as an important access point for passengers or freight.Power is supplied by a voltage of 2.5V volts.It is a part of family [0].A chip with 100pins is programmed.This device also displays [0].It is possible to construct digital circuits using 5000gates, which are devices that serve as building blocks.In general, it is recommended to store data in [0].This electronic part is mounted in the way of Surface Mount.There are 100 pins embedded in the device.It operates with the maximal supply voltage of 3.6V.It is powered by 3Vas its minimum supply voltage.A power supply of 1.8/3.32.5Vis required to operate it.Programmable I/Os are counted up 84.There is 166.67MHz frequency that can be achieved.It is recommended that the operating temperature be higher than -40°C.The operating temperature should be lower than 85°C.There are 16logic blocks (LABs) that make up its basic building block.If the maximal frequency is less than [0], it should be lower than that.A programmable logic type is classified as EE PLD.
EPM7256BTI100-7N Features
TQFP package
84 I/Os
100 pin count
100 pins
1.8/3.32.5V power supplies
16 logic blocks (LABs)
EPM7256BTI100-7N Applications
There are a lot of Altera EPM7256BTI100-7N CPLDs applications.
- POWER-SAVING MODES
- White goods (Washing, Cold, Aircon ,...)
- Storage Cards and Storage Racks
- Software-driven hardware configuration
- Interface bridging
- D/T registers and latches
- Software Configuration of Add-In Boards
- DMA control
- Protection relays
- Power up sequencing
