EPM7512AEQC208-10N
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | PQFP |
| Number of Pins | 208 |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 208 |
| ECCN Code | 3A991 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Frequency | 125MHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Pin Count | 208 |
| Operating Supply Voltage | 3.3V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 3V |
| Number of I/O | 176 |
| Memory Type | EEPROM |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 10 ns |
| Frequency (Max) | 116.3MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 10000 |
| Number of Programmable I/O | 176 |
| Number of Logic Blocks (LABs) | 32 |
| Speed Grade | 10 |
| Output Function | MACROCELL |
| Number of Macro Cells | 512 |
| JTAG BST | YES |
| In-System Programmable | YES |
| Height Seated (Max) | 4.1mm |
| Length | 28mm |
| Width | 28mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
EPM7512AEQC208-10N Overview
There are 512 macro cells. A macro cell is a cell in a mobile phone network that provides radio coverage through the use of a high-power cell site (tower, antenna or mast).It is embedded in the PQFP package.The device is programmed with 176 I/Os.There are 208 terminations programmed into the device.This electrical part has a terminal position of QUADand is connected to the ground.An electrical supply voltage of 3.3V is used to power it.This part is in the family [0].There are 208pins on the chip.There are 10000 gates, which are devices that acts as a building block for digital circuits. In order to achieve high efficiency, the supply voltage should be maintained at [0].It is recommended that data be stored in [0].This device is mounted by Surface Mount.The pins are [0].This device operates at a voltage of 3.6V when the maximum supply voltage is applied.Normally, it operates with a voltage of 3VV as its minimum supply voltage.There are a total of 176 Programmable I/Os.This can be achieved at a frequency of 125MHz.In order to operate properly, the operating temperature should be higher than 0°C.There should be a temperature below 70°Cat the time of operation.There are 32logic blocks (LABs) that make up its basic building block.A maximum frequency of less than 116.3MHzis recommended.There are several types of programmable logic that can be categorized as EE PLD.
EPM7512AEQC208-10N Features
PQFP package
176 I/Os
208 pin count
208 pins
32 logic blocks (LABs)
EPM7512AEQC208-10N Applications
There are a lot of Altera EPM7512AEQC208-10N CPLDs applications.
- Discrete logic functions
- POWER-SAVING MODES
- D/T registers and latches
- Multiple DIP Switch Replacement
- Power Meter SMPS
- Cross-Matrix Switch
- ANALOG-TO-DIGITAL CONVERTOR (ADC)
- Boolean function generators
- Random logic replacement
- Preset swapping
