FPF2125
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 30mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | IntelliMAX™ |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 160mOhm |
| Subcategory | Peripheral Drivers |
| Power Rating | 667mW |
| Max Power Dissipation | 667mW |
| Technology | MOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Current Rating | 1A |
| Base Part Number | FPF2125 |
| Number of Outputs | 1 |
| Output Voltage | 6V |
| Output Type | P-Channel |
| Max Output Current | 1.5A |
| Operating Supply Voltage | 5.5V |
| Voltage | 5.5V |
| Interface | On/Off |
| Current | 1A |
| Output Configuration | High Side |
| Power Dissipation | 667mW |
| Output Current | 600mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 25 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 1.8V |
| Max Input Voltage | 5.5V |
| Rise Time | 12μs |
| Fall Time (Typ) | 200 μs |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 70 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.8V~5.5V |
| Driver Number of Bits | 1 |
| Min Current Limit | 150mA |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 0.8A |
| Rds On (Typ) | 125m Ω |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Height | 1.25mm |
| Length | 3mm |
| Width | 1.7mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FPF2125 Overview
It's?packaged?in?the way?of?a?Tape & Reel (TR).The SC-74A, SOT-753 package includes it.A Surface Mount mounting is used for the LED driving board.There is a switch type of General Purpose.It is recommended that the temperature be set to -40°C~85°C TA for reliable performance.In this LED driver, there are no outputs available.A supply voltage of Not Required is required for it to operate.A maximum output voltage of P-Channel volts can be achieved by this LED driver.As you can see, it comes from the FPF2125 family.It contains 5 terminations.In order to operate, the 5 pins are used.As far as functions are concerned, the lighting driver has 1.In order to meet the operation criteria, the maximum output current drops to 1.5A.With a supply voltage of 3.3V, high efficiency is possible.Surface Mount is mounted in the way of this lighting driver.Currently, the LED driving board has a resistance of 160mOhm ohms.This electrical component can be found in the IntelliMAX? series.As a result, the output current is set to 600mA.A self-contained container with a capacity of Peripheral Drivers contains this lighting driver.In order to optimize the efficiency of the supply voltage, it should be set to 5.5V.This LED driving board can accept voltages up to 5.5V volts as an input.The input voltage minimum is 1.8V volts.
FPF2125 Features
Supplied from 3.3V
Resistance of 160mOhm
FPF2125 Applications
There are a lot of ON Semiconductor FPF2125 Power Switches ICs applications.
- Various applications equipped with buttons
- Wireless/Networking Cards
- Wireless Modem Data Cards
- Handheld Devices
- Telecom and Network Systems
- Solid-State Drives
- Hot-Swap Systems
- Portable GPS Device
- Smart Phones, Feature Phones
- Portable GPS
