Parameters | |
---|---|
Factory Lead Time | 1 Week |
Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
Mount | Surface Mount |
Mounting Type | Surface Mount |
Package / Case | 8-SOIC (0.154, 3.90mm Width) |
Number of Pins | 8 |
Weight | 230.4mg |
Operating Temperature | -40°C~85°C TA |
Packaging | Tape & Reel (TR) |
Published | 2014 |
Series | AccuPower™ |
JESD-609 Code | e4 |
Feature | Auto Restart, Power Good, Slew Rate Controlled, Status Flag |
Pbfree Code | yes |
Part Status | Active |
Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
Number of Terminations | 8 |
ECCN Code | EAR99 |
Type | General Purpose |
Resistance | 88mOhm |
Terminal Finish | Nickel/Palladium/Gold/Silver (Ni/Pd/Au/Ag) |
Subcategory | Peripheral Drivers |
Max Power Dissipation | 1W |
Terminal Position | DUAL |
Terminal Form | GULL WING |
Number of Functions | 1 |
Supply Voltage | 12V |
Base Part Number | FPF2700 |
Output Type | N-Channel |
Max Output Current | 2A |
Operating Supply Voltage | 36V |
Interface | On/Off |
Nominal Supply Current | 2A |
Output Configuration | High Side |
Output Current | 2A |
Voltage - Supply (Vcc/Vdd) | Not Required |
Input Type | Non-Inverting |
Turn On Delay Time | 2.7 ms |
Switch Type | General Purpose |
Topology | Charge Pump |
Min Input Voltage | 2.8V |
Number of Inputs | 1 |
Max Input Voltage | 36V |
Nominal Input Voltage | 36V |
Turn-Off Delay Time | 100 μs |
Ratio - Input:Output | 1:1 |
Voltage - Load | 2.8V~36V |
Driver Number of Bits | 1 |
Fault Protection | Current Limiting (Adjustable), Over Temperature, UVLO |
Output Peak Current Limit-Nom | 0.4A |
Rds On (Typ) | 88m Ω |
Max Junction Temperature (Tj) | 125°C |
Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
Ambient Temperature Range High | 85°C |
Height | 1.75mm |
Length | 4.9mm |
Width | 3.9mm |
Radiation Hardening | No |
REACH SVHC | No SVHC |
RoHS Status | ROHS3 Compliant |
Lead Free | Lead Free |
The AccuPowerM FPF270X series is a series of current-limiting OAD switches that provide FuI protection for the system and load under excessive current conditions. The minimum current limit is adjustable between 0.4A and 2.0A. The FPF270X includes a conversion rate-controlled N-channel MOSFET and conversion rated conduction to prevent power bus interference caused by hot-swappable loads or instantaneous overload requirements. The input voltage ranges from 2.8V to 36V. The load can be activated or deactivated by low voltage. Error flag pins and / or power good pins can be used to monitor pin failure conditions that are logically compatible.
Each member of the FPF270X series provides a class of load failure responses. All devices clamp the load current so that it cannot exceed the current level of external programming. The high temperature feature provides further protection when the power consumption is too high.
2.8 V to 36 V Input Voltage Range TypicalRDs(on)=88m
0.4 A to 2 AAdjustable Current Limit(Min.) Slew Rate Controlled
ESD Protectedabove 2000 VHBM Thermal Shutdown Active LOW Enable UVLO Protection Power-Good Output
Motor Drives
Digital Cameras
Consumer Electronics Industrial Computing
Hard Disk Drives
Telecom Equipment