FPF2702MPX
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WDFN Exposed Pad |
| Number of Pins | 8 |
| Weight | 151mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2017 |
| Series | AccuPower™ |
| JESD-609 Code | e4 |
| Feature | Power Good, Slew Rate Controlled, Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 88mOhm |
| Terminal Finish | Nickel/Palladium/Gold/Silver (Ni/Pd/Au/Ag) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 1.25W |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | FPF2702 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Max Output Current | 2A |
| Operating Supply Voltage | 36V |
| Interface | On/Off |
| Output Configuration | High Side |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.8V |
| Max Input Voltage | 36V |
| Nominal Input Voltage | 36V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.8V~36V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, UVLO |
| Output Peak Current Limit-Nom | 0.4A |
| Rds On (Typ) | 88m Ω |
| Built-in Protections | OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Height | 750μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FPF2702MPX Description
The FPF2702MPX is a series of current-limit load switches that safeguard systems and loads from excessive current circumstances. The minimum current limit can be set anywhere between 0.4 and 2.0 amps. To prevent power bus disturbances caused by "hot plugging" loads or transient excess load demands, the FPF270X includes a slew-rate-controlled N-channel MOSFET and slew-rated turn-on. The input voltage ranges from 2.8 to 36 volts. An ON pin that is compatible with low-voltage logic can be used to activate or deactivate loads. The error flag pin and/or the power-good pin can be used to monitor fault circumstances.
FPF2702MPX Features
2.8V to 36V Input Voltage Range
Typical RDS(ON)=88m
0.4A to 2A Adjustable Current Limit (Min.)
Slew Rate Controlled
ESD Protected, above 2000V HBM
Thermal Shutdown
Active LOW Enable
UVLO Protection
Power-Good Output
FPF2702MPX Applications
Motor Drives
Digital Cameras
Consumer Electronics
Industrial Computing
Hard Disk Drives
Telecom Equipment
