FSA1156P6X
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 2.7V |
| Base Part Number | FSA1156 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 100nA |
| Power Dissipation | 180mW |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 20pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 30ns |
| Charge Injection | 20pC |
| Switch-on Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 2.1Ohm |
| Normal Position | NO |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FSA1156P6X Overview
Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. A total of 6 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 2.7V volts, the electrical component should be turned on and run. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching with FSA1156 if you're looking for variants. In this multiplexer, the internal resistance is 900mOhm. For functions related to 6 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Digital switch that provides Single power at a cost-effective price. It is recommended to use 1.65V as the lowest voltage for the electrical part. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. A voltage higher than 500nA may cause damage to the switch multiplexer. It is possible to transfer data over a 300MHz-bandwidth. There is 2.1Ohm resistance between Drain and Source for this electronic part.
FSA1156P6X Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 300MHz
Drain-to-Source resistance: 2.1Ohm
FSA1156P6X Applications
There are a lot of ON Semiconductor FSA1156P6X Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- High reliability control systems
- HDTV
- Audio and video switching
- CSU
- Microprocessor Controlled Analog Systems
- Routers
- Digital cross connects (DSX-1)
- Central office
- Remote Powered Equipment
